TRIUMPH HERALD REVIEW

Still one of the best classics for charm, practicality and DIY simplicity...

With a maximum of 61bhp from the later 13/60, the Herald is a rather genteel, but accurate steering and a good gearchange allow you to pootle around without too much bother. Even the earliest Heralds can nudge 70mph, though 1200s introduced disc brakes, which are preferred. Refinement isn’t a huge strong point, but it’s all part of the Herald’s charm, although the high gearing doesn’t suit all tastes or driving styles. Stay away from the limits and you can corner briskly and safely. Indeed, bends can be taken quickly by employing the racing type drift corner, a technique to which the Herald adapts itself beautifully and gives absolute safety, together with a certain amount of thrill for both driver and passengers. Convertibles offer the benefit of sun-worship for four in comfort, which is a real boon on warm summer days. If you fancy a bit more go, the number of Spitfire tune-up goodies comes in handy, but consider suspension and braking modifications if you intend to boost the power output significantly.

VITAL STATISTICS

Engine                                    51cc/4-cyl/OHV

Power (bhp@rpm)                  51bhp@5200rpm

Torque (lb ft@rpm)                 63lb ft@2600rpm

Top speed                                78mph

0-60mph                                  25sec

Consumption                            34mpg 

Gearbox                                    4-spd manual

WHAT TO LOOK FOR

BODYWORK & CHASSIS

Check for rust on the leading edge of the bonnet, the wheelarches and around the headlamps. With the bonnet open, check the bulkhead, especially around the brake and clutch fluid reservoirs. Spillage here strips the paint and allows rot to gain a foothold. The front of the chassis is usually sound, often helped by regular drips of engine oil.

ENGINE

The engines are surprisingly hardy, but watch for blue smoke and a regular knocking that suggests a worn bottom end. Be especially wary if a 1500 engine has been fitted, as they offer more power, but a weaker crankshaft. Check the engine starts well from cold and that it pulls well during a road test. Gearboxes can get noisy with age. If it all goes nice and quiet in fourth, suspect worn layshaft bearings. Watch for jumping out of gear, especially when you release the throttle after accelerating. Synchromesh can fail too – second is usually the first to go. First gear never had synchromesh. A reconditioned gearbox will set you back around £250. A wobbly gearlever might just be worn bushes – a cheap and easy fix if that’s the case.

BRAKES

The steering allows that famous turning circle of 25ft. It should be direct and free of play, so if you have to fight to keep the car in a straight line, something is probably amiss. Wear can develop in the trunnions, which need regular lubrication with a heavy oil. Ask the seller whether this is carried out and how often - every 1000 miles is the recommendation. Ideally, you should jack the car up and try to wobble the front wheels. The front suspension is simple coils and wishbones, but worn dampers will make the car very skittish and bouncy.

The rear suspension is the weak point. Pushed hard, a Herald may suffer wheel-tuck, which brings in severe oversteer. Some fit Spitfire-type swing-spring kits, but with Herald power, the chance of you upsetting the back end are fairly remote. Tired dampers can make the back end feel very unsettled, but more of an issue is a tired road spring allowing the back end to sag and upset the balance of the car.

INTERIOR

Check the state of the interior. They can get very dog-eared if neglected and are surprisingly expensive to put right. Rimmer Brothers sells complete interior re-trim kits – for doors, side panels and seats, from £1220. It also includes sound insulation, seat foam and a new headlining. Water ingress is the main issue. Tired windscreen and door seals won’t help, but nor does the bolt-together construction. A well-constructed Herald should not bang and rattle unduly on the road, so avoid ‘loose’ examples.

OUR VERDICT

The Herald is still remembered fondly as one of the best small cars built in Britain. It may have lacked sophistication compared to its rivals, but it was well conceived given the limitations forced upon Triumph at the time. The pretty coupé is rare but stylish, the convertible surprisingly practical and not too hard to find. Estates and vans are very rare – most led hard lives – but the saloon is by far the most common. Yes, you can unbolt the roof if you trust to good weather, though make sure a convertible is genuine. The rear body was stiffened on the latter, so check that any converted saloons have had the requisite adjustments made during the process.

But it’s that swing-up bonnet and sheer simplicity that are a large part of the appeal. Few classics are easier to work on. The Herald is the ultimate in Meccano-like construction, and that does little to diminish its appeal. 

BENTLEY 8-LITRE REVIEW

Produced as an Entry level Bentley, and aimed at a slightly younger market, the Bentley Eight was a storming sales success.

Based heavily on the Bentley Mulsanne but with many of the luxuries removed (for instance the Bentley Eight came with steel wheels and cloth seats, with leather an optional extra). The car was distinguished by it's uncharacteristic wire mesh grill, as opposed to Bentley's usual slatted un it; this was a nod toward the marque's sporting heritage and another grab at the younger motorist.

Powered by the Mulsanne's 6.75L V8 mated to the same automatic transmission, the Eight did have a slightly sportier feel than the Mulsanne thanks to its tighter suspension. When looking to buy a second-hand Bentley Eight, main dealers or Bentley specialists are probably the best bet, with parts and accessories still readily available and after-care service that is second to none. Main dealers or specialists are the best bets when buying a used Bentley but some knowledge of what to look for will help you to find the right car. Later cars are preferred by collectors as these came with alloy wheels, fuel injection and ABS, with dark blue and greens being more desirable than black, white or red body-work.

Despite extensive use of Aluminum in the cars production wheel arches are prone to rust. Also the Eight is a likely candidate for unscrupulous dealers swapping the clocks when mileage gets high, to combat this Bentley mark the glass in the dash every time they change a clock; look for two white dots. The Bentley Eight was discontinued in 1993 after an extremely successful sales run.

BENTLEY S3 REVIEW

Launched in 1962, the Bentley S3 and its Rolls-Royce equivalent, the Silver Cloud III, employed the 6.2-litre aluminium alloy V8 engine introduced on the S2, though with larger carburettors, a new distributor, raised compression ratio, and came with a four-speed automatic transmission as standard equipment. Most obvious changes from the S2 were the adoption of a four-headlamp arrangement, the absence of side-lights from the wing tops, and a slightly lower radiator shell.

Inside, there was revised accommodation with separate front seats and increased room for rear passengers. James Young Limited and the now combined firm of H.J. Mulliner, Park Ward Limited continued to offer designs on the Continental chassis, and for the first time these were sanctioned on the equivalent Rolls-Royce, the Silver Cloud III. The Bentley Continental chassis now differed from the standard and Rolls-Royce versions only by virtue of its more comprehensive instrumentation.

By far the most striking of the Continentals were the Koren-designed coupes produced by Mulliner, Park Ward, these 'Chinese-Eye' models - so called because of their slanting headlamp nacelles - constituting the majority of coach-built S3 Continentals, 311 of which were made between 1962 and 1966. Much rarer in convertible form.

TRIUMPH SPITFIRE REVIEW

Pretty styling and simple mechanicals make an early Spitfire a tempting proposition, but what’s it like to buy?

Even in a fairly light car such as this, less than 70bhp from a small engine is never going to set the tarmac alight. And so it proves with the Spitfire, the 0-60mph sprint taking a leisurely 15 seconds and three-figure speeds out of reach without a (very) favourable tailwind. 

What this pretty soft-top Triumph is really about, though, is fun. And fun is something the Spitfire delivers by the bucket-load. Despite what the figures might say, there is enough pep to easily keep up with modern traffic, especially if you make good use of the light and accurate gearchange. 

The optional overdrive of MkII models does make longer distances a little easier, but the Spit is an easy car to row along while you just enjoy the top-down experience. Light, accurate steering is a boon around town as is the tight turning circle. The brakes are adequate but it pays not to be too exuberant in the corners, as the swing-axle rear suspension has potential to surprise in the wrong hands. It’s not as unpredictable as some would have you believe, but a modicum of caution is needed in slippery conditions. 

The ride isn’t exactly cosseting – the leaf-sprung rear end making things a bit choppy (though no worse than an MG Midget) – but with the roof down and the sun out such things are easy to overlook.

What is a plus point is the snug but comfortable cabin, the low seating position giving a real impression of speed even when travelling at a modest pace. Very early cars are a bit basic, admittedly, but the few switches and dials are perfectly placed, the driving position is fundamentally sound and everything is within easy reach so you should be able to get comfortable. The MkII got better seats and carpets, by the way. 

The Spitfire might lack a few creature comforts then, and refinement isn’t a strong point, but, make no mistake, it’s a very capable little sports car.

VITAL STATISTICS

Engine                                    1147cc/4-cylinder/OHV

Power (bhp@rpm)                  67bhp@5000rpm

Torque (lb ft@rpm)                 67lb ft@3750rpm

Top speed                                92mph

0-60mph                                  15secs 

Consumption                           32mpg

  Gearbox                                    4-spd manual

WHAT TO LOOK FOR

BODYWORK & CHASSIS
 

The bodywork can hide a whole host of corrosion-related sins and first stop are the sills – a major structural element on the Spitfire – so problems here will seriously affect the integrity of the body. If they’ve been replaced, you need to ensure it was done correctly as failure to brace the shell can result in it twisting, so check panel gaps and door alignment carefully. The rest of the panels should also come in for scrutiny, particularly the bonnet, inner and outer wings and wheelarches, A-pillars, and front valance. Safest thing is to assume any rust bubbles are significantly worse underneath. 

Replacements are common but the chassis is actually quite robust. Nevertheless, inspect it closely, paying special attention to the outriggers behind the front wheels that support the bulkhead. Rotten floorpans are common – rust can spread from flaky sills so check those too, not forgetting the suspension mountings particularly where the rear leaf spring attaches and the low points by the rear axle. Sub-standard restorations are always a risk with cars of this age, so make sure you’re happy with the car’s history and the standard of any work – putting things right can be a labour-intensive and costly process with a Spitfire.

  ENGINE

Both versions used a 1147cc engine derived from the Triumph Herald’s. It’s a reliable unit and great accessibility makes it a cinch to work on. Watch for oil leaks and tired cooling systems, but the main check is for worn crankshaft thrust washers – excessive play at the pulley is the giveaway. In the worst case, they can drop out, terminally damaging the crank and block. The correct oil filter will ensure oil doesn’t drain back to the sump, leading to top-end wear on start-up, and it’s worth listening for the rumble of worn big-end bearings.  It’s an easy unit to rebuild so general wear and tear isn’t a major concern. 

RUNNING GEAR

The four-speed manual gearbox can suffer from worn synchromesh and whining from tired bearings. You need to check thoroughly for oil leaks, but that’s about the extent of the problems, and replacement is fairly straightforward. Overdrive was optional on the MkII so check it engages correctly – if not, it is normally electrical problems or lack of oil in the unit. Lastly, listen out for clunks from worn UJs and ensure that engine oil leaks haven’t contaminated the clutch causing slippage. MkII models got a stronger diaphragm spring clutch as part of the updates.

Easy access to the running gear means repairs are simple, but it’s worth checking a few things. The front trunnions need to be oiled with EP90, not greased, so check the seller knew that. Worn bushes and balljoints are other issues and you need to watch for sagging rear leaf springs and play in the steering rack. Don’t ignore noisy rear wheel bearings as they are tricky to fix. 

INTERIOR

The cabin of an early Spit is as simple as they come, with MkII models getting better seats and carpets as standard. It’s a case of checking general condition but, with most parts available, refreshing a tired example isn’t costly. The hood on these early cars was a complex affair so check the condition of the hood and frame. A hardtop was optional on the MkII so make sure it’s not hiding a rotten soft-top.  

OUR VERDICT

 It may not be fast, but the styling alone should ensure it a place on your shortlist. It’s fun to drive, too. There’s a real feel-good factor to the Spitfire, and as long as you avoid the rusty ones, it makes for a great ownership proposition.

Triumph Spitfire

BENTLEY S2 REVIEW

Bentley's new S-series cars replaced the R-type range at the 1955 Earls Court Motor Show.

The Bentley S1 was powered by the company's well-proven 4.9-litre smooth six-cylinder engine of the R type, with twin SU carburettors. Coil and wishbone independent front suspension was new, and with four-speed automatic transmission, the S1 was able to convey its occupants in an ambience of leather seats and walnut veneer to speeds approaching 100mph. With development of its dependable six-cylinder engine nearing an end, and facing competition from faster rivals in the United States market, Bentley turned to V8 power as the 1960s approached. A radical change was to appear in 1959 with the introduction of the General Motors inspired 6,230cc V8 engine.

There was now adequate power to achieve a sustainable top speed of around 115mph. Although slightly heavier than its predecessor, the new Bentley S2 boasted a creditable 11.5 second dash to 60mph from rest. The new engine was an entirely new departure for Bentley, which caused some consternation among traditional Bentley customers. In the event, the V8 engine was a huge step forward, setting the standard for the rest of the century. The Standard Steel coachwork of the S-series cars proved extremely popular, having a certain dignity and yet fitting the traditional Bentley sporting image behind the winged B radiator.

TRIUMPH STAG REVIEW

V8 power, four seats and Michelotti styling – the noble Stag has it all. We explain how to buy this handsome Brit bruiser

Unlike its Spitfire baby brother, the Stag is more GT cruiser than back road barnstormer, something that’s reflected in the multi-adjustable driving position; even the steering column can be tweaked for rake and reach. Press-on enthusiasts prefer the rarer manual/OD cars, but we reckon the auto suits the car’s relaxed demeanour rather better.

Triumph 2000 owners will feel right at home behind the wheel, since much of the cockpit furniture is very similar, but this is by no means a criticism – quite the reverse, in fact.

The 3.0-litre V8 majors on low-down torque, making it ideal for covering long distances, and it makes at least as wonderful a noise as the Rover V8 that was so often transplanted into Stags during the 1980s. It’s a bit heavier than the Rover unit, but the car leans more toward lazy oversteer when provoked than miles of dreary understeer.

VITAL STATISTICS

Engine                                    2997cc/V8/OHC

Power (bhp@rpm)                  145bhp@5500rpm

Torque (lb ft@rpm)                 170lb ft@3500rpm

Top speed                                112mph

0-60mph                                  11.85sec

Consumption                            21.5mpg 

WHAT TO LOOK FOR

BODYWORK & CHASSIS
 

Rust is an obvious concern – it’s a product of BL circa. 1970s, after all. Take all the usual suspects – wheelarches, inner/outer sills, floorpan – as a given for examination, but there are other, more specific areas to consider. Areas of the panel ahead of the bonnet, for instance, are in the direct firing line of thrown-up stones. The unusual swage lines above the outer headlights have vertical faces than can be tricky to repair, since they’re not easy to align with the adjacent wing and bonnet. Cheap pattern parts are to be avoided here. It’s a similar story with the panel beneath the grille/headlights, although localised repairs are easier here. Also check the front and rear top wing seams – filler is common here.

Staying on the shiny side of the car, the rear panel around the tail-lights is vulnerable to rot, likewise the lower rear valance. The leading edge of the bootlid can trap moisture beneath the chrome trim strip and rot from within, too. Bodged repairs in the A-pillar can ultimately cause those big doors to sag slightly on their hinges, so check for proper alignment within the door frame.

Moving underneath the car, the main suspect to examine up front is the vulnerable front crossmember (which is sited directly beneath the radiator – and whose lower support is also prone to rust), but it’s crucial to ensure the chassis rails and outriggers are all sound. The rear floorpan warrants particular attention, as do the subframe mountings.

ENGINE

Much has been said about the Stag’s 3.0-litre V8 engine – most of it not terribly complimentary – and while it deserved pretty much every criticism it received in period, usually for overheating, most have been sorted by now. Key to reliability is use of a coolant containing a corrosion inhibitor – failure to do so causes the alloy cylinder heads to corrode and warp and the waterways to become clogged with silt. Radiators and associated plumbing should ideally be routinely replaced every 10-12 years.

RUNNING GEAR

The V8 demands regular (every 30,000 miles) replacement of the single-roller timing chains if it is to reach 150,000 miles between rebuilds. Death rattles from this area should set alarm bells ringing, since chipped teeth or – worse – complete breakage will cause a catastrophic valves/pistons impact. Check the hydraulic timing chain tensioners, too – they rely on engine oil for lubrication, so low oil level/pressure is bad news. Wear in the shaft bearing that drives the water pump, distributor and oil pump is one likely cause of low pressure.

Transmission options are four-speed manual/OD or Borg-Warner Type 35 three-speed auto. The manual’s synchromesh will eventually wear, most likely on second and third gear, while layshaft wear is evidenced by a noisy bearing sound that disappears when you dip the clutch. Worn driveshaft universal joints will cause automatic upshifts to lurch rather than slur, although too high an idle speed can have a similar result. The diff’ is strong, but will start to whine with age. Steering and brakes are largely tough and dependable, though the former can spring leaks over time.

Trim is largely durable, and cossetted cars should be fine. In any case, much of it is still available, so a tatty interior shouldn’t be a deal-breaker on an otherwise good car. Look out for a cracked glovebox surround (where the passenger seat rests when tipped forward) or dashtop (UV damage) and baggy seats (collapsed inner foam and rubber).

OUR VERDICT

Find a sorted Stag, and you’ll be in possession of a soulful, family-friendly GT car that still turns heads – as much for its burbling V8 sound as its beautiful Italianate lines. Its impressive survival rate – allied to slowly rising values – goes to show its enduring popularity. Factor in exceptional parts backup and one of the biggest, friendliest owners clubs in the country, and the Stag’s case is complete.

CLUBS

Classic car clubs have a wealth of information about buying, maintaining and spares availabilty for their cars. Relevant clubs for this car are as follows:

Triumph Stag Register

View website

Triumph Stag

TRIUMPH TR2 REVIEW

If it’s a classic British roadster you’re after, you cannot afford to ignore the TR2.

Said to be the cheapest British car to top 100mph, the TR2 received plenty of plaudits from road testers of the time and "fun to drive" was a regular comment. And they were right, the TR2 is just that. 

Its 90bhp may not sound a lot today, but allied to compact dimensions and light kerb weight, it was more than enough to entertain an enthusiastic driver. 

The cabin is a mite cramped if truth be told and the steering wheel skims the thighs of tall drivers, but ignore these foibles and the Triumph is terrific fun to throw around. 

Big bumps will cause the rear end to skip around a bit but the otherwise secure handling inspires confidence. Which is more than can be said for the brakes, so a disc upgrade is a useful addition if you’re planning on regular use. A well-maintained engine should burst into life quickly and pick-up cleanly at all engine speeds, so you’ll need to investigate if this isn’t the case. But find a properly sorted example and the TR2 will prove a superb country lane entertainer.

VITAL STATISTICS

Engine                                    1991cc/4-cyl/OHV

Power (bhp@rpm)                  90bhp@4800rpm

Torque (lb ft@rpm)                 117lb ft@3000rpm

Top speed                                107mph

0-60mph                                  12sec

Consumption                            34mpg 

WHAT TO LOOK FOR

BODYWORK & CHASSIS
 

Check the wings, sills, floor panels, spare wheel well, A-posts, the bulkhead and scuttle, the boot lid, and the battery tray for corrosion. The single-skinned wings don’t tend to rust at the wheel arches, but the points at which they attach to the body vulnerable to serious rot.

Although fundamentally strong, the simple ladder chassis also demands careful attention. Rust is the first thing to look for, particularly around the suspension mounting points. Pay particular attention to the area just behind the front wishbones – if the chassis appears out of true, this is a sure sign of a prang somewhere in the car’s past. A close look at the panel gaps will also reveal any problems in this area. Lastly, watch out for poor quality restorations using cheap, reproduction panels. There are bodged cars around so ask to see the records (photographic if possible) of any refurbishment work.

ENGINE

The Standard engine is a reliable unit, and DIY-friendly too, but age and lack of maintenance will soon take their toll. Excessive exhaust smoke, rumbling main and big-end bearings, and worn tappets all point to an engine in need of a re-build, so factor this in to the asking price. Be wary of cars that have seen very little use as the wet-liner unit has a tendency to sludge-up, while the steel gasket at the bottom of the liners can rot causing oil and water to mix. The twin SU carburettor set-up rarely gives problems and overhauling them is a straightforward and fairly cheap task. Lastly, with a wide range of parts available quite a few owners tune and uprate the engine so make sure you know what’s been done on the car you’re looking at.

ELECTRICS

The top-model 300SE and 300SEL had air suspension, which was high-tech stuff for the early 1960s. The ride it gives is quite remarkable, but problems can be very expensive indeed to fix, and parts are not plentiful. Buy an air-sprung Fintail with your eyes wide open, and have the phone numbers of a specialist and your bank manager close at hand.

RUNNING GEAR

The four-speed manual geabox is a tough little unit but there a few things to watch for. There is no synchromesh on first gear, but it can wear on the other gears so this is something to check on the test drive, as are any odd noises caused by chipped gear teeth. A ‘box that is noisy in the first three gears but quiet in fourth will be in need of new layshaft owing to worn bearings – a chattering in neutral that disappears when the clutch is dipped is another sign. Overdrive was an option when new and worth seeking out for the improved driveability it brings.

The Lockheed back axle has a reputation for fragility and there is a tendency for the TR2 to break half-shafts under enthusiastic use. Oil leaks can be a common problem too. Upgrading to the later Girling unit from the TR3/3A is a worthwhile modification.

BRAKES

The drum brakes aren’t massively effective, and the drums themselves will go oval over time, so ensure the car pulls up straight on the test drive. Fitting the front disc brakes from the TR3/3A is another popular modification, as is the addition of a servo, so don’t be surprised if the car you are looking at has already been upgraded. 

An independent front end with coil springs and a live beam axle with semi-elliptic springs takes care of suspension duties. Check that regular greasing has been undertaken every 1000 miles as a lack of attention will cause rapid wear. An overhaul is neither costly nor particularly difficult. Watch for wear in the steering arms and trunnions and excessive play in the worm and peg steering. A conversion to a rack-and-pinion set-up is popular.

INTERIOR

The original plastic trim is easy to replace, just check for any broken switchgear or any unsympathetic modifications that spoil the originality. Wiring that has gone brittle with age can be an issue along with weak dynamos and starter motors.

OUR VERDICT

It was Triumph boss Sir John Black’s desire to emulate the success of MG that led to the rapid design and launch of the TR2. What the company delivered was a simple, but robust little roadster. Based on a pre-WW2 Standard chassis, it borrowed the proven 2.0-litre engine from the Vanguard model, making it a quick car. Few cars are as entertaining as a classic British drop-top and the TR2 is one of the best examples of the breed, while that straightforward and sturdy construction makes it hugely tempting now. 

That’s the good news. However, despite that simplicity, there’s plenty to watch out for before taking the plunge. Thanks to the healthy prices on the used market, there is plenty of temptation for untrustworthy vendors to make money from sub-standard cars. Find a good example though, and this old-school roadster will put a huge smile on your face every time you get behind the wheel. And that is surely reason enough to place the TR2 at the top of any buyer’s list.

A variety of badly maintained or poorly restored cars still find their way onto the market. Therefore a professional inspection is money well spent. Find a good one, and you’ll enjoy one of the finest little roadsters on the market. 

TRIUMPH TR3 REVIEW

Alongside the contemporary MGA, the Triumph TR3 is the ‘other’ popular British roadster from the 1950s. Simple and reliable, the TR3 could reach 110 mph and sold very well to customers who – fortunately – only had performance in mind. Besides that, the TR3 offers no real comfort, and its weather equipment lets water leak inside the windscreen when the car is driven in the pouring rain. That said though, comfort is not the primary criteria you consider when purchasing a TR3. On a sunny day, being able to completely remove the sidescreens makes for an interesting driving experience too! 
In period, sales climbed each successive year, peaking in 1959-60 – by which time the TR3A was the production model – at which time around 70 TRs were being built each working day. That was a remarkable figure for a sports model, and the TR3/3A range remains popular to this day. The TR3A was introduced in 1957, bringing a whole host of extras, including an optional 2.2-litre engine. The ‘A was then replaced by the much more civilised TR4 in 1961, marking the end of the side-screen era.

Driving a TR3 is an invigorating experience. The power to weight ratio is good, and the 2-litre engine is flexible enough to pull heartily from fairly low speeds. Heavy traffic can be negotiated at 20-30mph in top gear, while the car will even move off from a standing start in second gear. At the same time, it is only really above 2000rpm that the engine produces its real power.
Once on the move, the gearbox is a delight to handle, through its central stubby, short-throw lever. When the side-screens are removed there is plenty of elbow room, but space is restricted a little when they are in place. The steering itself is reasonably fast, at 2½ turns lock to lock, and includes an inch or so of free play at the rim. The ride in general is quite good. The short wheelbase and shock settings produce a certain amount of pitching over big bumps, but smaller irregularities are nicely absorbed. On the whole, the standard suspension setup offers a decent balance between ride and road-holding prowess. Post-1956 cars feature disc brakes at the front, meaning they stop pretty sharply too.

WHAT TO LOOK FOR

1 The principal value of any TR is in its bodyshell, so check this both closely and carefully. Rustproofing was poor on the production line, so most survivors have been restored at least once by now. That’s ok providing the work has been done well, but unfortunately that isn’t always the case, so make sure everything lines up. If the body has been removed from the chassis at any point, it may have twisted out of true, so check all panel gaps – ideally they should be both tight and even. 
The chassis should also be straight, so get the car on a ramp and have a good poke around underneath. Outriggers can rot badly, much like any of the car’s steel parts, but everything is available. Oddly enough, the bonnet and spare-wheel boot lid are the two areas least affected by rust, but check the rest of the bodywork carefully. Floorpans are particularly prone to rot.

2 TR engines are renowned for their longevity – 150,000 miles between rebuilds is possible, providing regular servicing has been undertaken. The important thing to check is oil pressure, with 50psi being the desired figure once the engine is good and warmed up. The tell-tale signs of wear are straightforward – rattling and blue smoke under acceleration. Rattling indicates the main bearings are on the way out, while blue smoke suggests worn cylinder bores and/or piston rings. Tappets can also get noisy over time, though adjustment to quell the racket is possible.

3 All side-screen TR’s used essentially the same four-speed manual gearbox. If overdrive is fitted to a TR3, it should be of the Laycock-de Normanville A-type variety, operating on second, third and fourth gears. Gearboxes are tough, but high-mileage examples will be suffering from wear. The synchromesh will give up eventually, but the first things to go are usually the layshaft bearings. If this has happened, you will hear a chattering noise at tickover in neutral, then silence when the clutch is dipped.  

4 Thanks to a worm-and-peg steering setup, TR3 handling is wonderfully vintage, if a little vague. Steering box leaks are common, so if the oil level isn’t checked regularly, then rapid wear is inevitable. Lots of play means the box is worn. 

5 TR3 suspension is uncomplicated and durable, though problems can occur. Chief of these is trunnion wear due to insufficient lubrication – LM grease needs to be pumped in at the front every 1000 miles. At the rear there may be broken/damaged springs or lever arm dampers, but they are a relatively cheap and simple fix. A complete suspension rebuild isn’t beyond the average home enthusiast, as the work is straightforward and costs are manageable.

6    A TR3 should be sitting on 4.5 inch wide steel wheels as standard, though wire wheels were an option. The latter have many potential issues, such as worn splines and broken, loose or just plain rusty spokes. You need to feel for play against the hubs and check for spokes that aren’t under tension. Some owners have also fitted wider TR5 and TR6 steel wheels. 

7    The TR’s interior trim is simple and easily replaced if it is in poor condition. Costs will obviously add up though, so assess what needs attention and take into account what it’ll cost to put it all right. It’s much the same story with exterior trim.

OUR VERDICT
The Triumph TR series of sports cars was designed to provide maximum performance at minimum cost. Triumph found success with the TR2, so the introduction of the TR3 was a natural progression. The frontal styling change to the egg box grille was a simple change, though many more important but less obvious upgrades occurred during the TR3’s life. The engine first benefited from the high port head, then the change to 1¾-inch SU carburettors, resulting in a power boost to 100BHP.
Engineering development, assisted by the works competition programme, continued to the point where the TR was refined into arguably the most reliable, rugged and competitive sports car available in the late 1950s. To this day, the TR3 still manages to accomplish that objective in an exhilarating manner. Find a good one, and you won’t go far wrong.

TRIUMPH TR4 REVIEW

As British as they come, Triumph’s pretty TR4 is a potent and muscular sports car whose values are increasing steadily. We look at the pros and cons of buying one today

Classic Triumph TR4 Review

If you’re looking for deadly accurate steering and handling to shame an Elise, then look elsewhere: this is definitely a sports car in the old-school (1960s) sense of the word. Independent rear suspension didn’t arrive until the advent of the later (1965-67) TR4A, but the all-synchromesh gearbox (with some cars totalling seven gears, thanks to optional overdrive on second, third and fourth) and rack-and-pinion steering made the TR4 feel like a quantum leap over the preceding TR3.

It can be hustled along with aplomb on twisty country roads, that’s true, but in some ways this more an accomplished grand tourer than a screaming sportster. You really could imagine crossing countries in this car. The compact, yet comfortable cabin has it all, from the classic sprung steering wheel to the myriad dials (often sunk into an aftermarket or TR4A-style slab of polished timber). It feels more hemmed in the TR3, which used cut-down doors, but also less exposed to the elements. 

VITAL STATISTICS

Engine                                    2138cc/4-cyl/OHV

Power (bhp@rpm)                  100bhp@4600rpm

Torque (lb ft@rpm)                 127lb ft@3350rpm

Top speed                                104mph

0-60mph                                  10.9sec

Consumption                            22.5mpg 

WHAT TO LOOK FOR

BODYWORK & CHASSIS
 

It’s a British car from the 1960s, so unless a prospective purchase has evidence of extensive professional restoration, there are plenty of rot spots to investigate. The separate chassis is an added complication, making it often easier to effect repairs with the body off. All the usual places corrode with the worst of them, so check the leading edges of the bonnet, bootlid and doors, windscreen surround, the tops of the rear wings, the sills, floorpan and A-pillars.

Noticeably inconsistent shutlines, particularly around the doors, should start alarm bells ringing, as chances are the root cause is a distorted chassis, either as a result of previous accident damage or a terminally rotten chassis. You really need to get the car up onto a ramp to check this properly.

ENGINE

It takes quite a bit of neglect to see off a TR4 four-cylinder engine, so keep a weather eye out for death rattles (indicating shot main bearings) and blue exhaust smoke (worn piston rings and/or cylinder bores) under load. Anything less than 60psi oil pressure is bad news, although replacing the oil pump and/or big end bearings has been known to improve matters dramatically. Chattering valve gear can often be silenced through judicious adjustment, but beware seeping oil from either the timing chain cover or rear of the crankshaft. 

ELECTRICS

Electrics are of the knife-and-fork variety, and if even elementary repairs are beyond your abilities most garages will do routine work for relatively little money. Do try all the controls, however; a non-functioning heater can point to a terminally silted-up engine block, while repairing inoperative windscreen wipers is a dashboard-out job.

RUNNING GEAR

TR4 transmissions are inherently tough, but will require attention after 100,000 miles or so, specifically to the layshaft bearings. Erratic overdrive engagement can often be cured by expert adjustment. Don’t discount non-overdrive cars out of hand, either, since swapping an overdrive into a standard car is easier than you might think. Worn synchros can often soldier on for hundreds of miles with careful driving, but a re-build will probably be needed sooner rather than later. Listen for unpleasant noises accompanying take-up – the culprit is most likely one or more of the universal joints fitted to the propshaft and/or half-shaft, but it could also be a differential that’s about to part company with its mountings. 

  BRAKES

Many TR4s have been upgraded to modern springs and telescopic shocks by now – this is a problem only if you’re a stickler for period originality, since the original lever arm dampers were considered only average at best even when relatively new, especially on uneven road surfaces. One of the biggest TR4 headaches is poorly maintained trunnions – lack of lubrication causes them to dry out and seize, which in turn places undue stresses on the lower wishbone droplinks. 

 INTERIOR

Interior trim is generally hard wearing, but unrestored cars will be looking tired by now. Sagging seats – and the driver’s one in particular – are often accompanied by damaged side bolsters; a re-build and re-trim are the only viable long-term solutions. Finding a car with the much sought-after Surrey hardtop is a real bonus since prices for this factory option are very much in the ascendancy.

OUR VERDICT

Just take a look at this car and you’ll know why you want one – there’s not an iffy angle or line anywhere to be seen on Michelotti’s masterpiece, from the rounded front to the abrupt rear end. Factor in the grunty 2.1-litre ‘four’, which elicits an evocative growl from the exhaust, and there can be few finer companions on a sunny back-road blast.

It’s surprisingly practical, too (especially compared to the preceding TR3/3A) sporting a spacious cabin and a particularly accommodating boot. Certainly, you could take one on a long-haul run and not have to skimp too much on your luggage allowance.

Reassuringly uncomplicated, the TR4 sports a separate chassis and mostly bolt-on panels, which obviously makes home repairs and restoration that much easier. Triumph parts back-up is second to none, too, so if you can’t find a particular widget for your car, chances are there’s an alternative available.

Best of all, these cars can only increase in value.

The subtly upgraded, but considerably rarer TR4A tends to be the car that many buyers actively seek out – this despite the inevitable higher asking prices – but the standard car is much more readily available and good ones will have had most, if not all of their problems ironed out by now. 

It’s easy to succumb to the power-mad six-cylinder charms of the later TR5/6, but while the TR4’s four-pot has a murky past (it can trace its roots back to a Ferguson tractor), it is torquey and mellifluous, and can easily be maintained by the enthusiast DIY ownera paThey are a particularly tempting medium-term investment. At the very least, you won’t lose any money; chances are your return will improve considerably.

TRIUMPH TR5 REVIEW

Combining Michelotti’s glorious lines with six-cylinder power and fuel-injection, the Triumph TR5 is arguably the pinnacle of the TR series.
Continuing the type of innovation that the TR series had become known for – the TR3 marked the first production application of front disc brakes, while the TR4A was the first quantity produced sports car in its class to benefit from independent rear suspension – the TR5 brought new-fangled petrol-injection to the masses.
Launched as a stop-gap model in 1967, it’s sixcylinder engine was basically a longer-stroke version of the Triumph 2000 unit, with most of the additional oomph coming from the PI setup, improved exhaust manifolding and a much fiercer camshaft. Power was a claimed 150bhp, achieved at 5500rpm, providing the new model with impressive levels of both grunt and performance.
Appearance wise, not a lot differed from the TR4A it replaced, with the fabulous Michelotti lines largely unfettered. The reason for this was that Triumph simply weren’t in the position to stump up for a completely retooled body, especially for such a low-volume production car. Exterior revisions were restricted to a modernised grille, matt black sills, a bright sill trim strip and prominent tail badging, including the allimportant ‘injection’ motif. Moving to the cockpit, ventilation was improved with the use of eyeball vents, while the array of switches were now concealed by a safety conscious hood.
With a purchase price of just over £1200, the TR5 was great value for money compared to many of its contemporaries; indeed, almost 3000 found homes in just over a year of production. However the improved performance wasn’t enough to mask the fact that the basic body-shell had been in the public eye since 1961 – something which was addressed in late 1968 with the following TR6.
The annals of history show the TR5 as something of a shooting star then, one that burned brightly, but not for very long.

On the road
The TR5 is anything but subtle – when you turn the key you really know about it, your ears assaulted by an aural commotion of impressive proportions. The venerable straight-six kicks into life with gusto, while a prod of the accelerator pedal yields a satisfyingly throaty rasp. The 5s weren’t known for their smoothness on tickover when new, and this one is no exception. Idling at just 600rpm, the engine is endearingly lumpy, to the extent that you almost begin to wonder if all is well under the bonnet. Thankfully it all starts to make sense once you head out onto the open road. Once that hairy cam comes on song you’re rewarded with silky smooth delivery, while there’s impressive amounts of power available from as low as 1500rpm.
Once good and warmed up, the car absolutely implores you to drive it in a determined fashion. With that celebrated 150bhp to play with, thanks to the once infamous Lucas fuel injection, it remains one quick piece of kit too. There’s more than enough grunt to press you back into the slim short-back seats as you accelerate away, the rear end squatting as all that torque explodes onto the tarmac. The IRS suspension inherited from the TR4A means it rides well too, although there’s still lashings of the scuttle shake evident with all short-chassis Triumphs. As you’re moving along the road, one thing that does strike you is just how low down you feel in comparison to everything else on the roads today. This isn’t a problem though, as the height of the doors are sufficient enough to envelop all but the tallest of drivers, giving a reassuring sense of security as you hustle along.
With a gearbox descended from the very first TR2s, the change is somewhat notchy and agricultural in nature. That’s no real criticism however; it’s precise enough and easy to get the hang of, and as long as you don’t try and rush things when a change of ratio is required, you can slot the gearlever home like a good ‘un. The rack and pinion steering feels nicely weighted, though its not the most progressive of setups it has to be said; initial understeer can turn very quickly into lairy oversteer if you put your right foot down too vigorously, especially mid-corner. Cornering ability is undoubtedly high though, despite the power oversteer, and once you become accustomed to the rather ragged progress that is at times almost forced upon you, then the 5 is great fun to drive.
No wonder then that the Triumph TR5 is one of the most sought after TRs that money can buy.

BENTLEY R TYPE REVIEW

Looking for a classy Bentley oozing panache? Here we have the Bentley R-Type...

Rolls-Royce commenced production post-war with the Silver Wraith and Bentley MkVI models. For the first time there was standard coachwork, though the standard steel body - produced by the Pressed Steel Company, of Oxford - was available at first only on the Bentley, the equivalent Rolls-Royce - the Silver Dawn - not appearing until 1949. The range featured independent front suspension, hydraulic front brakes and a new 4,257cc, six-cylinder, F-head (inlet-over-exhaust) power unit, the latter destined for enlargement to 4,566cc in 1951. A much-needed improvement to the standard bodywork arrived in mid-1952 in the shape of an enlarged boot together with associated changes to the rear wings and suspension, subsequent models being known as the R-Type Bentley and E-Series Silver Dawn. The two newcomers were the first Rolls-Royce products available with automatic transmission, the company having opted for General Motors Hydra-Matic, a state-of-the-art four-speed unit that permitted manual selection. The standard R-Type was a lively performer, achieving 106mph in silence and reaching 50mph from standstill in 10 seconds despite a kerb weight approaching two tons. 2,322 R-Types had been produced by the time the model was superseded by the S-Type in 1955.

TRIUMPH TR6 REVIEW

The car that the clichéd term ‘last of the hairy-chested British sports cars’ was perhaps designed for, the TR6 has been a firm favourite for over 40 years.

The TR6 cabin experience is a snug one, particularly for six-footers, who may prefer a smaller diameter or dished steering wheel to feel more comfortable. Once you’ve settled in though, the controls fall readily enough to hand. The gearbox requires a firm touch, particularly when cold, but offers a change that is both positive and rewarding. Slotting home gears are a pleasure, especially when you make full use of the torque offered up by the sonorous straight-six engine – it’s worth holding off the changes a little longer, better to enjoy the delicious, rasping exhaust note. 

If you’re aboard an original CP-series then all the better – they have that bit more urge than the CR models introduced in mid-1972, which were given a milder camshaft for smoother driving in traffic. Carburettor-fed ex-US cars are naturally down on power, but still have plenty of poke. Whatever model you go for, look forward to masses of grunt and an invigorating driving experience. Standard brakes are more than up to the task, while the independent rear suspension provides much more composed handling compared to earlier TRs equipped with live axles.

VITAL STATISTICS

Engine                                    2498cc/6-cyl/OHV

Power (bhp@rpm)                  150bhp@5500rpm

Torque (lb ft@rpm)                 164lb ft@3500rpm

Top speed                                120mph

0-60mph                                   8sec

Consumption                            25mpg 

Gearbox                                    4-spd manual + Overdrive

WHAT TO LOOK FOR

BODYWORK & CHASSIS
Start from the rear when assessing a TR6’s bodywork. Go to one corner and look down the coach line. There should be a gradual side curve from front to back. Check to see that both sides are the same. If they are not, or one side is particularly curvaceous and the other is flat, then be particularly wary. This could be down to either accident damage, or simply a poor rebuild/restoration. 

Examine each of the four wing panel joints for rust, paint, bubbling or signs of local repairs. More importantly, check that the interface is visible and has not been overlaid and hidden with body filler. The rear wing/rear deck joints are particularly worth studying. You are looking for signs of soft sealer having been coated on the panel faces before the wings were bolted to the shell.

Underneath the car, run your hands along the flat of the chassis,feeling for two things – that the chassis is generally free of corrosion, but is also straight and true. Any rippling suggests accident damage. A key area to check is the ‘T-shirt’ pressing ahead of the differential. Four pieces of chassis meet there, so assess their condition thoroughly. This pressing is a highly stressed part of the chassis, as are the arms that radiate away from it carrying the trailing arm rear suspension. If repairs are required, budget on paying a professional to do the work.

ENGINE

With the six-cylinder engine, it’s vital to check the amount of crankshaft end float. With the engine switched off, lever the front crankshaft pulley backwards as hard as you can. At the same time, have someone depress the clutch pedal. If you see any movement, use a tape measure to check the extent of it. Any more than 11⁄16" or 1.5mm means attention is required.

Broadly speaking, TR6s come in home market/ROW fuel-injected specification (CP/CR), or carburettored US form (CC/CF). Only CP cars have the famed 150bhp. CR series cars, from mid-1972, were detuned for extra driveability in traffic, with only 125bhp on tap. US cars make do with a measly 104bhp. Carburettors rarely give trouble and are seen by many as being easier to maintain. Once in good condition though, the Lucas fuel injection can be made to perform very well however. Most worries stem from the overworked Lucas injection pump – replacement with a modern Bosch style item is thoroughly recommended. Check the correct engine is fitted – MG, MN, MM and MP prefixes signify a Triumph saloon unit, specifically 2.5PI, 2.5PI, 2.5TC and 2500S respectively.

RUNNING GEAR

Gearboxes are generally tough, but make sure all gears shift smoothly. A TR6 driveline features six universal joints, or UJs. Listen for clonking when taking up drive, as this generally means either the propshaft or driveshaft UJs are past their best. The rear hubs are a common malady. The bearings for them are sealed and they often fail, so be wary.

BRAKES

Other problem areas are where the trailing arms for the rear suspension and differential are attached to the chassis. Look carefully at where the trailing arms mount to the chassis. If there is rust there then you’re probably better off looking for a sounder candidate. Repairing or replacing these sections is very time and labour intensive, usually requiring a body off repair. On a test drive, listen for clunks coming from torn diff mounts – aknown weak point on these cars. A recognised – and well recommended – modification is to box in the diff’ mounts for added strength.

OUR VERDICT

The Triumph TR6 ranks as one of the most popular British sports cars ever made. Introduced in 1968 for the 1969 model year, it was basically a re-skinned TR5, complete with fuel-injected, six-cylinder engine mounted to an IRS chassis. Regular coachbuilder Giovanni Michelotti was unavailable, so German firm Karmann stepped up to the plate instead, producing a sharp redesign, but still utilising the same body tub. Both TR5 and TR6 are largely identical within the wheelbase – a nifty trick that probably saved Triumph a tidy amount of money in re-tooling at the time. 

In period, more TR6s were produced than any TR before it. The last fuel-injected TR6 was made in February 1975, while production of the ‘Federal’ car staggered on in strangulated form until July 1976. When it was finally replaced by the TR7 later that year, over 94,000 examples of the ‘6 had rolled off the Canley production line. This means that there are still large amounts of survivors to choose from now, so you can afford to be quite picky in your search. On a sunny day, on a twisting A-road, you’ll struggle to beat a good TR6 for driving satisfaction.

If you are looking ahead to the summer with open-top motoring in mind, you’d do well to consider a TR6. The bare facts make a lot of sense – superb back-up from both clubs and specialists, allied to a relatively high number of cars available mean you won’t go far wrong, providing you buy a good one in the first place. The last point is particularly crucial however. For the more hard-nosed buyer, a decent TR6 will make a good investment too – the rarity and desirability of the preceding TR5 has seen prices of that model skyrocket in recent years. A knock-on effect being that the TR6 is following suit as people cotton onto the fact they are pretty much the same car underneath. Prices are nowhere near ‘5 levels yet, but have certainly strengthened over the last few years, and are sure to rise. Getting in now – at the right money of course – should prove a shrewd investment.

Triumph TR6

TRIUMPH TR7 REVIEW

Drop down into the TR7’s cabin, and most likely the first thing you’ll notice will be the immense depth of the plastic dashboard. It had to be like that to accommodate the steeply-raked windscreen that was so much a part of Harris Mann’s wedge design. However, there’s a quite cosy cockpit-like feel around the driver, and that’s a plus. But you might be surprised by how little stowage space there seems to be in the cabin. 

Acceleration is adequate but not sparkling, and if you’re driving an automatic car, expect slurry rather than crisp changes. Second and third gears in the five-speed cars give a satisfying surge of power. There’s quite a satisfying rasp from the exhaust, too, although the four-cylinder engine is never going to sound as good as the six in earlier TRs – or as good as the V8 in the TR8, for that matter.

The brakes are good and responsive, and the steering OK but not especially sharp or quick. The handling in general makes a TR7 feel more like a small saloon than a real sports car, but that was the way of the 1970s. 

VITAL STATISTICS

Engine                                    1998cc/4-cyl/OHV

Power (bhp@rpm)                  105bhp@5500rpm

Torque (lb ft@rpm)                 119lb ft@3500rpm

Top speed                                109mph

0-60mph                                  9.1sec

Consumption                            27mpg 

Gearbox                                    5-spd manual

WHAT TO LOOK FOR

BODYWORK & CHASSIS
New body panels ran out years ago, but specialists have manufactured reproduction panels and repair sections. On the cosmetic side, look for rust in the front wings, front body panel, pop-up headlamp pods, and inner wheel arches at both ends.

For structural rust damage, number one check should be the sills. Examine the inside faces by peeling back the carpets, and make sure that the outer sills are proper panels and not just "cover sills"; a proper full-length sill extends behind the front wing. On convertibles, look also for rust in the boot floor, inner rear wings, and the inside of the rear quarter-panels. One area to check very carefully on both coupés and convertibles is the trailing arm mounting points. 

Many fixed-head TR7s came with Webasto fabric sunroofs. These had wooden frames which can soak up water and rot through: a clue is staining on the headlining. Repairs to damaged sunroofs can be surprisingly expensive.

At the front of the car, check the windscreen frame. Rot can start under the chrome trim and affect both the lower frame and the upper, including the front edge of the roof. 

ENGINE

The one mechanical problem you don’t want is an overheating engine. The alloy cylinder head corrodes, waterways clog, and the head then warps. The temperature needle should not stray past the "normal" mark. 

ELECTRICS

Contrary to popular belief, the pop-up headlamps do not give a lot of trouble, although getting them to perform in fully synchronised harmony can be a job beyond even the most patient owners. 

RUNNING GEAR

A four-speed gearbox was available up to 1978, and isn’t much liked. It had its origins in the Marina, and high-mileage examples will suffer from weak synchromesh and may jump out of gear on the over-run. The five-speed available from 1976 and standard from 1978 was the LT77 type that was also used in Rovers, Jaguars, Range Rovers and Land Rovers, so it’s pretty tough. Listen for a rattle under power in third gear, which usually means the fluid is low, and remember that the fluid for these gearboxes is automatic transmission fluid; using thicker ordinary gearbox oil results in baulking synchromesh and you might not get the box into second when it’s cold! 

A common problem on TR7s that haven’t been used for some time is a sticking clutch. The five-speed gearbox depends on splash lubrication, so towing the car and dumping the clutch at speed might free your clutch, but it might also wreck your gearbox!

BRAKES

Finally, a steering vibration between 50 and 60mph is quite common, and can be hard to eliminate. So it need not be a deterrent to purchase unless it’s severe or there are indications of steering or road wheel damage.

OUR VERDICT

No doubt about it: the best buy for maximum fun is a late convertible, with the five-speed manual gearbox rather than the automatic option. It gives open-air motoring in a manner which is a brilliant compromise between the old manner and the modern cocooned style.

On the other hand, if you want maximum value for money and don’t really care for the open air, get the best coupé you can find. For what they offer, the cars are under-priced, and a coupé really does make sense as characterful everyday, all-weather transport.

The cost of repairs means it really isn’t worth buying a basket-case for restoration, so such cars are best considered as sources of spares only. However, if you enjoy DIY work and know what you’re doing, why not uprate to Sprint specification? You can buy all the necessary parts. 

Die-hard TR fans were pretty rude about the TR7 when it was new, and it’s certainly not a hairy-chested sports car in the tradition of the TR6 it replaced. Today, though, it makes an affordable and pleasant way of getting into TR ownership, especially in convertible rather than fixed-head form. Properly maintained cars make reliable classics and can provide plenty of fun.

Once you know why you want one, the next problem is deciding which one you want. The TR7 was introduced as a fixed-head coupé in 1975 and didn’t become available as a convertible until 1979. Coupés were built until the end in 1981 but don’t have the following that the convertibles enjoy. 

TR7s were built in three factories. The earliest cars were all built at Speke, by a disaffected and strike-prone workforce. They weren’t generally built well. After one strike too many, production was transferred to Canley in 1978, where quality went up by leaps and bounds. Then from 1980, TR7s were built at the Rover plant in Solihull, and some people say these were the best of the lot. 

BENTLEY T-SERIES REVIEW

There’s no questioning the class and luxury on offer but should you buy a Bentley T-Series?

Essentially what we have here is a Rolls-Royce Silver Shadow fitted with Bentley trimmings, but while thousands of Shadows were made the T Series are rarer beasts.  For example, just 568 T2s were made and you would have needed deep pockets to get your hands on one with a purchase price of almost £37,000 in 1979.  But if your bank balance was suitably healthy you’d have been able to experience one of the most luxurious cars of its time, and one that still makes rather a special statement today. 

Slide into the leather-clad driver’s seat and you’re faced with a delicately thin-rimmed steering wheel and a dashboard covered in the finest timber.  This is a car that was all about comfort and unsurpassed opulence and it plays that role incredibly well, insulating the occupants from the distractions of the world outside and letting them just get on with enjoying the beautiful materials and craftsmanship.  And there’s plenty of toys to play with too, from the electrically-adjustable seats to air-conditioning that can deliver an Arctic blast at the flick of a switch.  So it’s certainly cossetting but what about the driving experience? 

Well, it proves as comfortable and relaxing as the imposing looks lead you to expect.  The ride is incredibly supple, helped by a kerb weight that simply steamrollers bumps into submission, and the handling isn’t as roly-poly as you’d think.  Sure, there’s impressive amounts of body lean if you get too enthusiastic but it never feels too unruly, especially if you keep to the more relaxed pace that the Bentley encourages.  In any case, the lack of support from the seats and the finger-light power steering doesn’t really tempt you to push too hard.  The powerful brakes inspire confidence though, which is just as well as planting the right foot into the Wilton reveals a surprising turn of speed.  Keep the throttle pinned in a T2 and sixty miles-per hour arrives in less than ten seconds, accompanied by a majestic rise from the nose, although fuel consumption that would shame a fighter jet soon puts paid to those antics.

VITAL STATISTICS

Bentley T2

Engine         6750cc/V8/OHV

Power          Not stated

Torque         Not stated

Top speed    120mph

0-60mph      9.4secs

Economy      14mpg

Gearbox        3-speed automatic

Weights and Measures

Height                     1518mm (59.7in)

Width                      1829mm (72in)

Length                     5194mm (204.5in)

Wheelbase               3048mm (120in)

Kerb weight             4809lb (2181kg)

WHAT TO LOOK OUT FOR

Major body repairs will have a calamitous effect on your bank balance, so every inch requires careful examination.  Amongst the key rot-spots are the front wings where they meet the sill, the front and rear valances, the inner rear wings, and the lower edges of the doors and boot lid.  The rear arches are prone too, and bubbling here almost certainly means worse horrors beneath so have a good feel around the inner lip of the arch.  The sills themselves also need careful checking as complete replacement can easily cost £4000 per side.  And it’s also worth looking for signs of galvanic corrosion where the aluminium panels meet the steel monocoque.

A look underneath is strongly advised as rust can attack the floor of the cabin and boot, and repairs here are a major undertaking – be wary of any signs of damp caused by perished and leaking screen seals.  And pay close attention to the condition of the paintwork and chrome as quality was top notch and repairs or replacement will be eye-wateringly expensive.

The carburettor-fed V8 – a 6.2-litre unit for the T1 and 6.75 litres for the T2 – lasts well but examples without a detailed service history should be viewed with suspicion.  Regular oil changes are required to prevent excessive camshaft wear and sludging of the hydraulic tappets, and correct anti-freeze levels are vital.  Annual coolant changes are recommended as internal corrosion leads to the build-up of sediment and serious problems with the cylinder liners, requiring a complete re-build at huge cost.  The unit also needs checking for signs of oil leaks, head gasket failure, and cracked exhaust manifolds.

The later GM400 3-speed automatic is deemed more reliable than the T1’s 4-speeder but check that gear changes are smooth and jolt-free.  The electric selector mechanism can play up though so ensure that all gears engage correctly.  It’s also worth checking for signs of oil leaks from the differential and any knocking that indicates prop or driveshaft joints that are past their best.

The suspension is a hefty set up comprising double wishbones and coil springs up front and semi-trailing arms at the rear and uses a complex system of hydraulics.  A specialist inspection is advisable for peace of mind.  Leaks caused by corroded pipework are the main concern, but you’ll also need to check for worn joints and bushes and for signs of corrosion around the subframe mounting points and rear spring pans.  A car that’s sagging at the rear or sits unevenly is a worry and with a complete overhaul costing thousands don’t be tempted to ignore signs of neglect here.

Equally complex is the braking system.  Specialist tools are required for many jobs and full refurbishment can approach £5000, so look for evidence of recent work or get it inspected if you’re not sure.  Fluid leaks and seized calipers need watching for, along with corrosion of the brake pipes where they pass over the rear subframe.  There are also more than ten flexible hoses that’ll need checking.  Replacement, which needs doing periodically, is fiddly and labour intensive so if it’s been done recently, so much the better.  And make sure the two brake warning lights on the dashboard illuminate and extinguish correctly – be very suspicious if not.  The T2 got rack and pinion steering but check for any signs of fluid leaks around the pump and pipework on both models.

The cabin of any Bentley is a real high point, and the T Series is no different.  Material quality is superb with the finest leathers and wood veneers, which means big bills if refurbishment is needed.  Make sure, then, that patina hasn’t become shabbiness.  There are plenty of electrical gadgets too, so make sure everything is working and pay particular attention to the operation of the air-conditioning.  The sheer cost of repairing a failed system may have led to it being ignored by previous owners.

OUR VERDICT

If you admire the Rolls-Royce Silver Shadow but find it a bit, whisper it, 'common', then the T Series is a superb alternative.  There are caveats, not least of which is terrifying restoration costs if you choose badly, and neither can it be run on a shoestring.  But few cars make you feel so good, and that alone makes it worth every penny.

BENTLEY T1 REVIEW

Drivers will love the Bentley T1 for its refined, laid back nature and raw power, while passengers will enjoy a standard of ride quality that few cars of the era (or any other era, for that matter) can match.

Once inside vast amounts of interior space, top quality hide and heavily engineered suspension more than make up for that, and the Bentley is one of the most comfortable cars on the road even today, delivering a soft, heavy-on-the-tyres, even roly-poly type ride.

The 6750cc V8 delivers its power in a gentle manner, but there’s plenty in reserve when you need it. The full 340lb ft of torque kicks in at just 1500rpm, so gaining speed is never an issue. 

They may have more sporting pedigree than Rollers, but Bentleys like this aren’t supposed to endure hard cornering. A T1 will grip reasonably well, but the feather-light steering and equally delicate throttle and brakes don’t really lend themselves to hooligan behaviour. Slot the skinny gear selector into Drive, head for the nearest country clubhouse and enjoy the T1 as it was designed to be enjoyed. 

VITAL STATISTICS

Bentley T1

Engine                                    6750cc/V8/OHV

Power (bhp@rpm)                  226bhp@4300rpm

Torque (lb ft@rpm)                 340lb ft@ 1500rpm

Top speed                                115mph

0-60mph                                  10.9sec

Consumption                            14mpg 

Gearbox                                    3-spd automatic

WHAT TO LOOK FOR

BODYWORK & CHASSIS
 

Bear colour in mind when choosing a car. Colours that were popular when the car was new won’t necessarily be in vogue today and can have an impact on desirability and value. Many T1s were finished in Honey Gold and Willow Gold, but they’re not nearly as in demand as neutral blues and greens. 

It’s no surprise that corrosion can be the Bentley’s biggest problem. The most common rot spots include the wing bottoms, wheelarches, sills and bumpers, none of which are cheap to put right. 

ENGINE

Low mileage cars aren’t always a good bet. If a car has next to no miles on the clock it will have been left standing for a long time. It’s better to buy one with a taller odometer reading that has been used and serviced regularly. It’s also worth finding a car that has had money spent on it – so you don’t have to. 

ELECTRICS

The top-model 300SE and 300SEL had air suspension, which was high-tech stuff for the early 1960s. The ride it gives is quite remarkable, but problems can be very expensive indeed to fix, and parts are not plentiful. Buy an air-sprung Fintail with your eyes wide open, and have the phone numbers of a specialist and your bank manager close at hand.

The air conditioning system is as complicated as the anchors. It’s over-engineered as there are nine actuators to operate the upper and lower systems, so there’s an awful lot to go wrong. If it needs any work then a good specialist is unlikely to replace the whole system, because there’s simply so 

much of it and it makes more sense to change the necessary parts. You’ll have to budget around £1000 for a new compressor and hoses. 

The T1 is fitted with far more luxuries than most cars of its era, many of which are electrical (the windows, mirrors, air conditioning etc). Spend a bit of time inside the car and try out everything to see whether or not it works. You can bank on a big repair bill if anything is awry. 

RUNNING GEAR

Gearboxes are prone to leaking, especially if the car has been standing outside for a long period. If you can, find out where the car is usually parked and inspect the ground for signs of leaks from the transmission. Early cars have a four-speed box. 

BRAKES

The complex braking system is a hydraulic set-up using Citroën accumulator spheres. If the engine cuts out then the accumulators can also fail, so you could end up with no brakes. Repairs are lengthy and expensive, as the rear subframe may need to be removed. To avoid buying a dud, look for a car with as much documentation as possible and history of maintenance on the brakes. 

INTERIOR

When inspecting the interior, make a point of lifting up the carpets. They’re so thick and plush that punters often don’t think to look beneath them, but they can be hiding serious water ingress and corrosion, so it’s always worth checking. Obvious as it might seem, a rotted carpet means that there are serious problems lurking beneath. 

Attention to detail makes all the difference with a Bentley or 

Rolls-Royce of this vintage. Tidy boots and gloveboxes, a watertight history, evidence of having been serviced by specialists and use of the correct lubricants can make a huge difference and are all signs that a previous owner has tretated the car with the necessary care and attention. A professional inspection by a specialist before you buy is also very much worthwhile.

OUR VERDICT

Few cars rival the T1 for luxury at this price other than its Rolls-Royce stablemates. But don’t be tempted by cars with rock-bottom price tags. The allure of a cheap Bentley may be strong, but it isn’t worth it unless you have double the budget for parts and you’re a dab hand with electrics, hydraulics and bodywork. 

It’s been said before, but there really is no substitute when it comes to shopping around and saving up to pay more for a good car. Restored cars with a paper trail and evidence of due care and attention are worth the extra money, as it’s so easy to plough tens of thousands of pounds into a rough one. Paying a specialist a nominal fee for an inspection and getting involved with the club scene before you buy will pay dividends, too. Do it by the book and you’ll bag one of the best British prestige cars money can buy. 

Raucous performance cars not your thing? Prefer to arrive at your destination in understated style, but with power to spare when it’s needed. You could buy a modern Bentley/Volkswagen for a six-figure sum – or you could set aside £10,000 (and maybe a little more) for a very tidy T1. 

Essentially a re-badged Rolls-Royce Silver Shadow, the T1 differs from the Roller only in its slightly different grille and a few Bentley emblems. Inside, it’s pure prestige, with the finest of leather seats, wonderfully thick carpets and more standard equipment than just about anything of a similar era. The simple styling renders this Bentley rather subtle in appearance, but its sheer size gives it an almost regal road presence. 

T1s and Silver Shadows enjoyed a lengthy production run, so there are plenty of them around. But the earliest models are now 45 years old, so time and lack of use has taken its toll on many. Budget for a cared-for car, though, and you’ll enjoy prestige classic motoring at its finest – for a fraction of what you’d pay for a modern Bentley.

TRIUMPH VITESSE REVIEW

Upmarket cars sporting a quartet of frowning ‘Chinese Eye’ quad headlights were all the rage in the 1960s. Jensen C-V8, Rolls-Royce Silver Cloud II, Bentley S3, Chrysler 300G/H – they were all at it. But surely the pleasingly aggressive-looking Triumph Vitesse is the most famous of them all. It’s remarkable to think today, then, how close the car came to never getting beyond the design stage.

Standard-Triumph may have enjoyed some glory years during the 1950s with the Triumph TR series, but as the 1960s dawned, it was clear that the company wasn’t in the greatest of financial health. In the event, it was a last-minute rescue package from Leyland Motors in 1961 that finally saved the company.

Project ‘Zobo’ – aka the Herald – went into production two years before Leyland entered the picture, but Standard-Triumph’s increasingly bleak-looking balance books suggested it wouldn’t survive for long. Plans had been in place to revive a curious and oft-maligned 1930s trend for small six-cylinder cars ever since the Herald’s inception, however, and with Leyland’s backing, the car entered development.

Ironically, the initial development hack – nicknamed the Kenilworth Dragster – packed a 2.0-litre Vanguard engine and was used by Technical Chief, Harry Webster, as his own car for several months. For production cars, however, an enlarged version of the Herald’s SC (‘Small Car’) ‘four’ was deemed more appropriate at 1600cc, with twin Solex carburetors upping power to 70bhp.

A Herald gearbox sporting tougher internals and closer ratios – but still no synchromesh on first gear – was deemed sufficient to handle the extra power, but, subtle changes to the suspension aside, the standard chassis was largely retained.

The car survived until 1966, at which point the Vitesse was upgraded with a 2.0-litre engine, stronger gearbox and better brakes, but it wasn’t until the 1968 advent of the Vitesse Mk2 that the swing-axle rear suspension was finally canned.

The factory sold 51,212 examples before it was phased out in 1971 in favour of the new Dolomite range.

VITAL STATISTICS

Triumph Vitesse 1.6

Engine 1596cc/6-cyl/OHV

Power 70bhp@5000rpm

Torque 110lb ft@2800rpm

Top speed 83mph

0-60mph 17.8sec

Economy 24.6mpg

Gearbox 4-speed manual + opt O/D

ON THE ROAD

No doubt about it: the Triumph Vitesse looks meaner than the proverbial junkyard dog just parked up on your driveway. It’s a good job, then, that it has the mouth to match the trousers, although the six-pot lurking beneath this particular car’s trademark tilt-front bonnet is the 70bhp 1600, not the later 2.0-litre mill, which mustered 95bhp.

It’s an appealing little ‘six’ nonetheless – it’s good for over 80mph in top, and while a 0-60mph time of over 17.5 seconds doesn’t sound like much to write home about, it feels much brisker in practice, not least as it weighs barely 920kg.

As with many six-cylinder engines, though, the Vitesse relies more on low-down torque than peaky horsepower to haul itself along. It’s no sluggard, but it works best when viewed more as a grunty mini-GT than a screaming out-and-out sportscar. It’s a pity, then, this car wasn’t specified with optional Laycock overdrive (which worked on third and top gear) to quieten things down at higher speeds.

Handling is largely benign and predictable at workaday speeds if the driver is smooth and gets his or her braking over and done with before diving into a corner. Provoke the notorious swing-axle rear suspension anywhere near the limit – especially in the wet – however, and it will eventually bite.

An unfortunate quirk of the Vitesse 6’s suspension is that ham-fisted over-exuberance in the bends can tuck a rear wheel into extreme positive camber and throw the car into snap oversteer. The resultant slide is often difficult to catch. Indeed, in its February 1969 test of the 2.0-litre Vitesse, Motor magazine was heard to complain: "One can’t help feeling that the Vitesse might have established a greater niche for itself if it had started life with a live axle."

EXPERT VIEW

"The test-drive of a Vitesse 1600 is crucial," says Jigsaw Triumph Specialists’ Mark Field. "Piston slap, which can be easily mistaken for pinking when you back off the throttle while stationary, and/or smoke on the overrun can signal a £450 bill for a new set of pistons. They’re expensive, because they’re only manufactured by a company in Australia. Fail to sort them out, however, and the engine can be damaged beyond reconditioning limits.

"Three-synchro gearbox whine in first is to be expected, but if it occurs in any other gear, it’s a sure sign of collapsing layshaft bearings. Often the best solution is to swap in a four-synchro gearbox from a Mk1 2-litre.

"Adjustable shock absorbers are the best way to tame swing-axle wheel-tuck, although you can fit re-cambered rear springs. As for body rot, check the main chassis rails, preferably with the car up on a ramp – repairs here must be professionally seam-welded for an MoT pass. Also check the outriggers as the body-chassis mounts, which are hidden behind the sills and bottom of the B-posts."

WHAT TO LOOK FOR

Bodywork

There are plenty of corrosion spots to watch out for, with the rear wings, the spare wheel well in the boot, the door bottoms and the sills (particularly around the attaching screws) prone to the dreaded tin worm.

Check the condition of the one-piece bonnet for signs of overspray or deformation – as the unit is one of the more expensive components to replace, signs of poor repair work can help to indicate if the Vitesse you’re looking at has any front-end collisions hidden in its history.

Pay particular attention to the front and rear wheel-arches, which are double skinned and should be checked carefully around the edges, as these will help indicate the condition of the car’s inner panels.

It also pays to make sure you know exactly what sort of Vitesse you’re inspecting – plenty of the saloon models have been converted into al fresco models, but they’re not as valuable as the factory-built ragtop models. You’ll be able to spotgenuine item by the anti-burst latches on the door and pillars, and the strengthening beams around the B-pillar. The commissioning plate should also read ‘CV’ (for convertible) – a chopped saloon will still have its ‘DL’ code.

Similarly, the early Vitesse 6 models had mesh radiator grilles rather than the horizontal slats of the later two-litre models – if the two don’t match, make sure you ask the seller why.

Engine and Gearbox

There are two versions of Triumph’s in-line straight six to choose from – the 1596cc version fitted to the original Vitesse 6 model, and the later 1998cc unit introduced in 1966. It’s a sturdy unit which should be capable of at least 100,000 miles with regular servicing, and its shared heritage with other Triumphs - particularly the GT6 – means it’s well catered for by specialists.

Thrust washers wearing out or dropping out altogether are a known trouble spot. Get a friend to start the car up and depress the clutch pedal while you watch what’s going on beneath the bonnet – if the front crankshaft pulley moves forward, it’s going to need replacing.

It’s also worth checking that the Vitesse you’re looking at has the engine Canley intended – the engine number on the 1596cc engines starts with HB, while the two-litre versions began with TC. If it begins with an M or K it’s come from another Triumph model (or even the Standard Vanguard Six) – not necessarily a bad thing, but a haggling point if the car’s being sold on its originality.

Running Gear

The biggest influence on your Vitesse buying tendencies should be the condition of the chassis – if it needs major surgery the bodywork will have to be in sound condition before it comes off.

Look for signs of accident damage around the front – wrinkles in the rails near to where the wishbones can provide clues to the car’s history – while the worst corrosion spots are towards the rear. Water collects in the dipped areas around the differential, and it can be a tricky area to repair.

Gearboxes generally last well and the clutch should be light and smooth to operate, and check that the overdrive works correctly in both third and fourth.

Check for rattles or clinks coming from underneath the car at the point of setting off – a worn universal joint or a loose bolt where the driveshaft connects to the diff are the likely candidates. Trunnion bearings are also prone to wearing out, particularly on the two-litre models, and any particularly gruesome wear points it not being oiled regularly.

Interior & Electrics

There are no particular horrors to look out for – most of the interior trimmings can be sourced easily if you shop around, although the sun visors unique to the convertible models can be tricky to get hold of.

Check for signs of scuffs or tears around the seats or carpets, and budget accordingly for repairs. Damp in the carpets in either of the footwells can point to corrosion in the metalwork beneath or a roof leak in the convertible models, so use any damp spots as potential bargaining chips.

OUR VERDICT

The Vitesse is rarer and faster than the Herald it’s based on, and thanks to the moody look created by that restyled front end has a character all of its own.

It’s also easy well catered for by Triumph clubs and marque specialists, who will be all too happy to point you in the right direction when it comes to parts and expertise.

Pay over the odds for a rust-afflicted example or a saloon pretending to be a convertible and it’ll be a headache, but do your homework and the right Vitesse is a fun route into six-cylinder route into Triumph ownership.

Triumph Vitesse

TRIUMPH SPITFIRE 1500 REVIEW

The last of the classic open-top Triumphs was also one of the best.

A long-running and bitterly fought automotive battle was finally drawing to a close by the end of the 1970s. For years previously, anyone looking to buy a small British open-top two-seater sports car bought either an MG Midget or a Triumph Spitfire, and die-hard fans frowned upon anyone who defected from one marque camp to the other. How ironic, then, that the final incarnations of each car should share the same 1500 engine. 

The Spitfire arguably had the last laugh, though: where the Midget latterly sprouted federal-spec plastic bumpers and a raised ride height, the Spitfire 1500 retained most of the earlier mark IV’s svelte chrome bumper good looks and would go on to last a year longer.

VITAL STATISTICS

Engine                                    1493cc/4-cyl/OHV

Power (bhp@rpm)                  71bhp@5500rpm

Torque (lb ft@rpm)                 82lb ft@3000rpm

Top speed                                101mph

0-60mph                                  13.2sec

Consumption                            28mpg

Gearbox                                    4-speed manual + opt OD

WHAT TO LOOK FOR

BODYWORK & CHASSIS
 

The main thing to bear in mind with the Spitfire is that it retains a separate chassis, so the sills are actually a key aspect of car’s structural integrity. Rusty sills, then, are not just a nuisance – they can write them off altogether. Check that the areas where the sills meet the floor are rot-free, and if possible, lift the carpets to check the state of the floor itself. Uneven panel gaps around the doors are a further clue to dangerously frilly sills – they can be indicative of a dangerously flexing body.

Elsewhere, the one-piece bonnet obviously comprises the front wings and wheelarches, and while aftermarket examples (in either steel or GRP) are readily available, they’re certainly not cheap. Blocked drain holes can also spell the end for the doors if they haven’t been routinely cleared by previous owners.

ENGINE

The Triumph 1500 engine hasn’t received the best press over the years, mainly owning to repeated dark mutterings over fragile bottom ends (worn crankshaft and main bearings in the main), but it’s a torquey little motor that responds well to sympathetic modernisation.

Aside from all the usual checks (blue exhaust smoke, ominous rattles and clonks), try to run the car up to full operating temperature. A steadily rising temperature gauge can be symptomatic of a water pump that’s about to expire or a blocked or damaged radiator. It’s wise to replace or refurb either of these on an unrestored car, but resist the urge to fit an electric fan – expert opinion suggests that it’s better to fit a larger radiator instead.

Poor hot-starting can often be resolved by binning the points and condenser in favour of electronic ignition, too, while returning later cars’ Waxstat-type SU carbs to standard specification often improves starting and running. Make sure the carb heat-shield is in good order, too.

RUNNING GEAR

If the Spitfire has an Achilles Heel, it concerns the front suspension. Cursed with notoriously fiddly and unforgiving brass trunnions, failure to oil these on a regular basis (every 3000 miles) can have dire and potentially spectacular ultimate consequences – left unlubricated long enough, the suspension will quite literally fall apart.

The news is little better out back, where there are more trunnions to lubricate and wheel bearings that were designed to incorporate grease nipples, but apparently left the factory with them blanked over. If greasing is neglected as a result, the bearing cages will fail, with replacements costing a couple of hundred pounds a side.

  INTERIOR

If the Spitfire has an Achilles Heel, it concerns the front suspension. Cursed with notoriously fiddly and unforgiving brass trunnions, failure to oil these on a regular basis (every 3000 miles) can have dire and potentially spectacular ultimate consequences – left unlubricated long enough, the suspension will quite literally fall apart.

The news is little better out back, where there are more trunnions to lubricate and wheel bearings that were designed to incorporate grease nipples, but apparently left the factory with them blanked over. If greasing is neglected as a result, the bearing cages will fail, with replacements costing a couple of hundred pounds a side.

OUR VERDICT

It seems frankly unfathomable that Spitfires, for whatever reason, have never quite fired the imagination of people looking to invest in their first classics as much as other marques. These are handsome cars that are great fun to drive, straightforward to work on and blessed with excellent spares and specialist back-up. Factor in an active and friendly owner’s club, and the case for choosing one is clear-cut.

BENTLEY TURBO REVIEW

Bentley hit upon a heady mix of performance and opulence with their definitive luxury saloon. But today a Turbo R can make a very tasty classic bargain too...

Boasting an enormous price tag when new – comfortably in excess of £100,000 by 1990 – the Bentley Turbo R is perhaps the luxury bargain of the modern age. The best thing is that they make absolute sense as a driving machine. A generous prod on the accelerator elicits a rush of energy that launches you past lesser road users. If you’re in a post-1990 model with clever active suspension, you’ll enjoy total composure in the corners, too. Tempted?

VITAL STATISTICS

1987 Bentley Turbo R

Engine                                    6750cc/8-cyl/OHV 

Power (bhp@rpm)                  330bhp@4000rpm

Torque (lb ft@rpm)                 480lb ft@2250rpm

Top speed                                140mph

0-60mph                                   7sec

Consumption                            14mpg

Gearbox                                    3-speed auto

WHAT TO LOOK FOR

BODYWORK & CHASSIS
 

The first Rs are now a quarter of a century old. So despite excellent build quality when new, they will rust if neglected. Rear wheelarches are particularly prone to rot if the car hasn’t been looked after. Make sure you examine up inside the arch, as well as down at either end of the sill. Water gets in at both ends, but especially the front. The rear valance can also corrode, and it is well hidden behind the rear bumper, so be thorough in your examination. 

Under the car, the front outriggers can rot on higher mileage cars, while the rear spring pans should also be checked closely for corrosion. You should also ensure that the extensive exterior chrome isn’t pitted, while those hefty, impact-absorbing bumpers should be straight and free from scratches.

ENGINE

Carburettor-fed examples (pre-1987) are less popular because the complex Solex four-choke unit has a poor reputation for reliability. They can also suffer from hot-starting issues, which is unheard of on fuel-injected models. Either should cruise beyond 200,000 miles without requiring major attention, provided proper service intervals have been respected.

Poor starting, pinking, uneven idling or lack of responsiveness could be caused by anything from a leaking inlet manifold to an engine management fault (on post-1994 cars). Take a test drive and keep a close eye on the temperature gauge – steer clear of anything that overheats. Coolant leaks can quickly become serious, so check carefully for drips or weeping hoses anywhere in the system. Minor oil leaks are par for the course on a 50-year-old engine design, but liberal coatings of oil on the underside should have you walking away. Leaking turbo oil feed pipes are another bad sign – a loss of oil feed will cause the turbo to fail, with potentially catastrophic results – so be on your guard.

RUNNING GEAR

Two sturdy GM automatic gearboxes were used throughout the production span of the Turbo R. The three-speeder used until 1992 is simpler, but the later four-speeder gives better flexibility, acceleration and economy. Both should find all their gears without hesitation. Transmission fluid should always look pink and clean. You might hear a whine from the differential on high-mileage cars, suggesting a hard life. They will go on like this for a while, but clunks or rumbles are a definite no-no.

Suspension-wise, both standard (pre-1990) and active suspension should provide excellent ride quality. A well looked-after car shouldn’t feel loose or sloppy, even over a poor surface. When they need replacing, the active dampers are very expensive, so haggle accordingly if this is required. Power steering is standard on all models, and leaks can occur from the pump, the rack and the connecting hoses.

INTERIOR

It is unlikely you will find a car whose cabin has been mistreated, but look out for dirty leather, worn carpets and pedal rubbers, and untidy boot linings. All of these point to a car that hasn’t been treated with sufficient respect. Veneer door cappings and dash sections can fade due to sunlight, so walk away from cracked or peeling varnish. 

OUR VERDICT

The Turbo R is a complex machine, so seek expert advice both before and after you buy. Buying one privately can be worth the saving over a specialist dealer’s price but, that said, you will be glad of a reputable trader’s guarantee should things start to go wrong. Be careful, though, as once you’ve got a taste for the high life, you may find it hard to settle for anything less in the future.

Check out this video of a Bentley Turbo R in Jay Leno's garage:

Bentley

BENTLEY TURBO R REVIEW

How do you improve an already excellent luxury saloon? Strap a whacking great turbo on to it, of course. We sample a tasty classic...

Boasting an enormous price tag when new – comfortably in excess of £100,000 in 1990 – the Bentley Turbo R is now the luxury bargain of the 21st Century. The best thing is that Turbo Rs make absolute sense as a driving machine too. A generous prod on the accelerator elicits a rush of energy that launches you past lesser vehicles. If you’re in a post-1990 model complete with clever active suspension, you’ll enjoy total composure in the corners, too. Tempted?

VITAL STATISTICS

1987 Bentley Turbo R

Engine                                    6750cc/8-cyl/OHV

Power (bhp@rpm)                  330bhp@4000rpm

Torque (lb ft@rpm)                 480lb ft@2250rpm

Top speed                                140mph

0-60mph                                  7sec

Consumption                            14mpg

Gearbox                                    3-speed auto

WHAT TO LOOK FOR

BODYWORK & CHASSIS
 

The first Turbo Rs are now 25 years old, so despite excellent build quality when new, they will rust if neglected. Rear wheelarches are particularly prone to corrosion if the car hasn’t been cared for. Make sure you examine up inside the arch, as well as down at either end of the sill. Water gets in at both ends, but especially the front. The rear valance can also corrode, and it is well hidden behind the rear bumper, so be thorough with your examination. Under the car, front outriggers can rot on higher mileage cars, while the rear spring pans should also be checked closely.

ENGINE

Pre-1987 carburettor-fed examples are less popular because the complex Solex four-choke unit has a poor reputation for reliability. They can also suffer from hot-starting issues, unknown on fuel-injected models. Either motor should cruise beyond 200,000 miles without requiring major attention, provided that proper service intervals
have been respected.

Poor starting, pinking, uneven idling or lack of responsiveness could be anything from a leaking inlet manifold to an engine management fault, the latter more common on post-1994 cars. Take a test drive and keep a close eye on the temperature gauge – steer clear of anything that overheats. Cooling leaks can quickly become serious, so check carefully for drips or weeping hoses anywhere in the system. Minor oil leaks are par for the course on a 50-year-old engine design, but liberal coatings of oil on the underside should find you walking away. Leaking turbo oil feed pipes are another bad sign
– a loss of oil feed will cause the turbo to fail, with potentially catastrophic results, so be on your guard.  

RUNNING GEAR

Two sturdy GM automatic gearboxes were used through the production span of the Turbo R. The three-speeder used until 1992 is simpler, but the later four-speeder gives better flexibility, acceleration and economy. Both should find all their gears without hesitation. Transmission fluid should always look pink and clean. You might hear a whine from the differential on high-mileage cars, suggesting a hard life. They will go on like this for a while, but clunks or rumbles are a definite no-no.

Suspension-wise, both standard (pre-1990) and active suspension should provide excellent ride quality. A well looked after car shouldn’t feel loose or sloppy, even over a poor surface. When they need replacing, the active dampers are very expensive, so haggle accordingly if this is required. Power steering is standard on all models. Leaks can occur from the pump, the rack and the connecting hoses. 

INTERIOR

It is unlikely you will find a car where the cabin has been mistreated, but look out for dirty leather, worn carpets and pedal rubbers, and untidy boot linings. All of these symptoms point to a car that hasn’t been treated with sufficient respect. Veneer door cappings and dash sections can fade due to sunlight, so avoid cracked or peeling varnish. Ensure exterior chrome isn’t pitted – the hefty, impact-absorbing bumpers should also be straight and free from scratches.

OUR VERDICT

Turbo Rs are complex machines, so seek expert advice both before and after you buy. Buying one privately can be worth the saving over a specialist dealer’s price, but you will be glad of a reputable trader’s guarantee should things go wrong. Rough examples can have a thirst for cash that’s bigger than their thirst for fuel. Get a good one, however, and it can be astonishing value for money. But be careful – once you’ve acquired a taste for the high life, you may find it hard to settle for anything less.

TRIUMPH 1300/1500 REVIEW

Good examples of these FWD saloons are getting hard to find - so buy one now...

Intended to bang a nail in the coffin of the long-running Herald and at the same time take on the popularity of the Austin 1100, Triumph obviously had high hopes when it launched its 1300 in 1965.

While it didn't actually achieve the sales that the company had in mind, Triumph's first front-wheel drive car did play a major role in the development of the Toledo, Sprint and Dolomites and introduced a well-proportioned saloon that has proved to be a very popular everyday classic.

Initially the 1300FWD used the same 1296cc engine from the Herald 13/60 it was supposed to be replacing. The unit was positioned above the gearbox in a front/back configuration that placed some ocnstraints on the car's design. However, stylist Michelotti produced a gret body style, following on from the look of the 2000, with a central airtake on the bonnet plus the subtle roofline terminating with a lip above the rear window.

In 1967 a twin-carburretor version appeared with the sportier 1300TC model, providing a further 14bhp and fitted with a brake servo to help control the extra power.

Significant revision came in 1970 with the introduction of the 1500FWD that saw the look of the car changed with twin headlamps and a seven-inch growth spurt.

VITAL STATISTICS

Engine: 1296cc/4-cyl/OHV

Power: 61hp@5000rpm

Torque: 73lb ft@3000rpm

Maximum speed: 85mph

0-60mph: 19.0sec

Fuel consumption: 29-33mpg

Transmission: FWD, four-spd manual

WHAT TO LOOK FOR

The rot pack

Be sure to check the front inner wing behind the suspension turret, as well as the usual rot spots - boot floor, chassis rails, door bottoms, front panels, jacking points, sills and wheelarches. Reproduction panels appear on websites occasionally but front panels and valances are becoming very hard to obtain.

Get your motor running

To get the best from Triumph's three bearing crank engine, make sure the oil is fresh and quality oil filters are used. The starter is unique to the 1300, as the starter ring is on the crank pulley - it rotates anti-clockwise. While in theory not suitable for unleaded fuel, some owners use unleaded and knock the timing back a couple of degrees.

Working on the inside

The FWD gearbox can suffer from weak second gear synchro but parts are availale and it can be rebuilt without removing the box from the car. The input shaft is another potentially weak spot. Canley Classics stocks an upgraded shaft and gear combination. If the clutch needs changing, it can be done from inside the car.

Interior items

The 1300FWD's trim is unique, but it is durable. It also has a different dashboard, carpets, door handles, locks anf even window winders. Headlinings tend to be glue-stained from the factory while rear seat uprights are prone to fading. Be careful with the instrument binnacle - a plastic moulding - which can crack when refitted. Water/damp in the footwells is a tell-tale sign of leaks from the windscreen.

Radiator/Cooling system/heater

There are two types of radiator - early cars have a single top hose while the later ones feature a double set up. Hoses are available from specialists ot the TDC.

Exhaust stock

New old-stock mild steel systems appear from time to time, while the TDC can supply a stainless system.

OUR VERDICT

Both the 1300FWD and 1500FWD cars offer great value for money with a satisfying mix of luxury and practicality. They are good-looking cars, fun to drive and capable of keeping up with contemporary traffic. The base model 1300FWD and 1500FWD cars generally offer the best deals though increasingly some models, particularly the 1500SE, are becoming rarer to source. People with good examples tend to hang on to them.

Club support is excellent for these cars, not just for camaraderie and parts supply, but also for finding decent cars with history details to match.